【2023】How to Fix Automatic Repair Loop in Windows 10/11?| How to Fix Startup Repair Issue in 4 Ways?

How to fix Automatic Repair loop in Windows 10? Follow this video to learn 4 ways to fix the startup issue. To recover lost data due to automatic repair loop, try Tenorshare 4DDiG: https://bit.ly/3xcr5pP
Read the detailed guide here: https://4ddig.tenorshare.com/windows-fix/fix-windows-10-automatic-repair-loop.html

An automatic repair loop is an error that occurs when Windows 10 tries to boot and fails, then forcefully boots up the automatic repair tool and tries to repair itself. When Windows can’t repair itself, it reboots and repeats itself in an endless cycle. In this video, we’ll show you 4 ways to fix this issue.

📌Timestamp
Video Intro 00:00
Method 1: Disconnect or Remove Recently Installed or Connected Devices 00:31
Method 2: Use Check Disk Utility 00:50
Method 3: Disable Automatic Startup Repair to Limit Boot Loops 01:38
Method 4: Perform Refresh or Reset Your PC 02:51
Bonus: Data Recovery using Tenorshare 4DDiG 03:09

🔻Method 1: Disconnect or Remove Recently Installed or Connected Devices
If you recently installed new hardware before a Windows 10 automatic repair loop began to appear, then the hardware you’ve installed is a likely cause of the problem.
In most cases, removing the problematic device will allow Windows to skip over the issue. If Windows boots with the device removed, you can then look at installing new drivers or replacing the component.

🔻Method 2: Use Check Disk Utility
The chkdsk command starts a low-level check of your system drive for errors using the Check Disk utility. If it detects errors, it will automatically repair them.
While Windows can’t boot, you can still force Windows to boot to a Command Prompt window using the Advanced options menu screen. Press F8 and launch the Command prompt window. Type chkdsk /f /r C: and then press Enter. Type exit and press Enter. At last, Restart your PC to see if the problem is fixed or not.

🔻Method 3: Disable Automatic Startup Repair to Limit Boot Loops
If you’re confident that a Windows 10 installation is still functional, then it’s possible to disable the automatic startup repair system. This should allow you to boot into Windows without the repair loop taking place. To do that follow these steps,

Step 1: Power on System and press F8 and wait for the boot troubleshoot menu to load, selecting See advanced repair to proceed.
Step 2: In the boot troubleshoot menu, select Troubleshoot – Advanced options -Command Prompt, then wait for the command line window to open. You may need to authenticate with your local or Microsoft account password first.
Step 3: In the command line window, type bcdedit and double-check the values for identifier and recoveryenabled. The identifier value will usually appear as {default}, with recoveryenabled listed as yes.
To change this, type bcdedit /set {default} recoveryenabled no to disable automatic boot repair.
If you’re running this command from a command line or PowerShell window in Safe Mode, you may need to replace the identifier value to {current} instead (e.g. bcdedit /set {current} recoveryenabled no).

🔻Method 4: Perform Refresh or Reset Your PC
If the Windows Automatic Repair loop issue still exists after trying the above six solutions, you can try the last method- performing refresh or reset to fix the Windows Automatic Startup Repair boot issue.
Step 1: Choose Troubleshooting when the Boot menu appears.
Step 2: Choose between Refresh your PC or Reset your PC.
Step 3: Follow the instructions to complete the process.

🔻Bonus: Data Recovery using Tenorshare 4DDiG
While resetting your PC, all your data will be lost, so after resetting your PC you may need to recover your desired files using a data recovery tool. Tenorshare 4DDiG is a professional data recovery software that can recover 1000+ data types including photos, videos, documents, and more with simply 3 steps.
Download Link for Win: https://bit.ly/3ICOow2
Download Link for Mac: https://bit.ly/3IztfTK
Step 1: Download and install the program on your system after resetting it. Launch the software and select a hard drive location and click Start to proceed. Then select the target file type to scan.
Step 2: Now, 4DDiG will start scanning the local hard drive to find the data.
Step 3: After the scanning, you can choose files to preview and then click Recover to save them to a different partition.

——————————————————— Follow Us—————————————————–
Facebook: https://www.facebook.com/4DDiG-Data-Recovery-105124668454036
Twitter: https://twitter.com/Tenorshare4DDiG
Quora Space: https://tenorshare4ddigdatarecovery.quora.com/
Pinterest: https://www.pinterest.com/4DDiG/_created/
Instagram: https://www.instagram.com/tenorshare_4ddig/
Subscribe to our YouTube channel and there are more tech tips and tricks for you.

source

how to repair windows 10