Computer NetworksNETWORKS

update Tenda ac23 to save wifi settings (atualize tenda ac23 para salvar as configurações)

your router does not save the settings when resetting, so your solution is here (seu roteador tenda naõ salva as configuraçoes ao resetar, entao sua solucao esta aqui)

link mediafire – https://www.mediafire.com/file/a75ec5a70wzdb41/US_AC23V1.0re_V16.03.07.37_cn_TDC01.bin/file

you will connect the router’s rj45 cable to the pc, open the page of the router 192.168.0.1, in the system configuration, and lan configuration, will change the lan address to 192.168.1.1, and in the allocation of ip address to 192.168 .0.10 ~ 100 and save. open the network and internet settings, tab ethernet and change options for adapter, right button on ethernet network cable, properties, 2 clicks on ip protocol ipv4, and use following ip address 192.168.1.13 – 255.255.255.0 – 192.168.1.1 and ok and ok. hold the reset button on the router, remove the power cord for 5 seconds without releasing the reset button, connect the cable and continue holding the button, open page 192.168.1.1 and go by clicking on F5 until the option appears on the page of your choice the file to update, just release the reset button when this option appears. put the china firmware US_AC23V1 that is in the link below and update, wait for the countdown time of 100 seconds, when reset, open the network and internet settings again, ethernet, change adapter, right button on ethernet cable, properties, 2 clicks in ipv4 protocol and put back to using ip address automatically and ok, ready, your router already has the firmware fixed that saves your wifi settings when reset or disconnect. note (since it is from china, everything will be in chinese, but you can use the google translator on google to see where the settings are.)

você vai conectar o cabo rj45 do roteador no pc, vai abrir a pagina do roteador 192.168.0.1, na configuração do sistema, e configuraçao de lan, vai mudar o endereço de lan para 192.168.1.1, e na alocaçao de endereço ip para 192.168.0.10~100 e salva. abra as configurações de rede e internet, aba ethernet e alterar opçoes de adptador, botao direito em ethernet cabo de rede, propriedades, 2 cliques em protocolo ip ipv4, e usar seguinte endereco ip 192.168.1.13 – 255.255.255.0 – 192.168.1.1 e da ok e ok. segure o botao resete do roteador , retire o cabo de energia por 5 segundos sem soltar o botao resete, ligue o cabo e continue segurando o botao, abra a pagina 192.168.1.1 e va clicando em F5 ate aparecer a opcao na pagina de voce escolher o arquivo para atualizar, so solte o botao resete quando essa opcao aparecer. coloque o firmware da china US_AC23V1 que esta no link abaixo e atualize, aguarde o tempo regressivo de 100 segundos, ao zerar, abra as configurações de rede e internet de novo, ethernet, alterar adaptador, botao direito em ethernet cabo , propriedades, 2 cliques em protocolo ipv4 e coloque de volta em usar endereco de ip automaticamente e de ok, pronto, seu roteador ja esta com o firmware consertado que salva suas configuracoes de wifi ao resetar ou desligar. observacao( por ser da china, vai ficar tudo em chines, mas voce pode usar o google tradutor no google para ver onde estao as configuracoes.)

source

ipv4

Alice AUSTIN

Alice AUSTIN is studying Cisco Systems Engineering. He has passion with both hardware and software and writes articles and reviews for many IT websites.

Leave a Reply

Your email address will not be published. Required fields are marked *